| Select | Model | Unit | Use | Specification | Other |
|---|
| | | | | | | |
| |  AC/DC Current Clamp CC-65 | pc | It is a transducer which allows
your multimeter to measure
current data and enable your
oscilloscope to measure
the current waveforms. | AC/DC Current Clamp,
20kHz Bandwidth, 1mV/10m,
65A. | Two types
connectors.
Type A:
Male BNC
connector;
Type B:
Banana
Connectors. |
| |  AC/DC Current Clamp CC-650 | pc | It is a transducer which allows
your multimeter to measure
current data and enable your
oscilloscope to measure
the current waveforms. | AC/DC Current Clamp,
20kHz Bandwidth, 1mV/10m,
650A. | Two types
connectors.
Type A:
Male BNC
connector;
Type B:
Banana
Connectors. |
| |  AC/DC Current Clamp CC-1100 | pc | It is a transducer which allows
your multimeter to measure
current data and enable your
oscilloscope to measure
the current waveforms. | AC/DC Current Clamp,
20kHz Bandwidth, 1mV/10m | Two types
connectors.
Type A:
Male BNC
connector;
Type B:
Banana
Connectors. |
| |  Probe (PP80, PP90, PP150, PP200) | pc | Integral injection molding makes
the usage more flexible and
the oscilloscope able to adapt
more testing situations. | Attenuation ratio: 1× and 10×
optional. Input resistance:
1MΩ: 10MΩ
System bandwidth:
x1:DC-4MHz-80MHz;
x10: DC-60MHz-200MHz. | Universal
version. |
| |  High-Voltage x100 Probe (T3100) | pc | The T3100 probe is designed
as a strong, flexible and
reliable part for the oscilloscope
according to the human body
function. | Attenuation: 100:1;
Input Resistance: 100M ohm;
Bandwidth: DC-100MHz;
Input Voltage:2000VDC+ACpk | Universal
version |
| |  20:1 Attenuator (HT201) | pc | The HT201 has been designed
to allow fuel injector and primary
ignition waveforms to be
measured using Hantek
oscilloscopes. | Specification: Attenuation: 20:1
Bandwidth: 10MHz
Input Res: 1.053M | For vehicle
testing. |
| |  Auto Ignition Probe (HT25) | pc | Auto ignition probe is a kind of
inductive capacitance sensor,
it must match with an
oscilloscope. | Lead length 2.5 meters, the decay
of up to 10,000:1. | For vehicle
testing. |
| |  Large Dolphin/Gator Clips (HT18A) | pair | The dolphin/gator clips are fully
insulated with a 4 mm socket
in the handle, offering an easy
connection to the HT30A auto
test cable. | Length: 85 mm, Height: 38 mm
Depth: 16.5 mm
Clamping limit: 30 mm
Contents:1pc X Red Clip
1pc X Black Clip | Be able to
use with
HT30A. |
| |  Multimeter Probe (HT19) | pair | The multimeter probes offer
a quick and easy solution,
where a permanent connection
is not required. | Length: 131 mm Diameter: 10 mm
Contents:1pc X Red Probe,
1pc X Black Probe | Be able to
use with
HT30A and
HT307. |
| |  Auto Test Leads (HT30A) | pc | It's a special line for assisting
auto measurement instruments
to test various types of signals. | Test lead of a male BNC
connector to (2) 4mm connectors.
4mm connectors are coded
in two colors, black and red.
Lead length 30 meter. | For vehicle
testing. |
| |  Breakout Leads(HT301) | pc | This breakout lead is easy to
take voltage readings from
numerous sensors in vehicle
engine compartment. | Connect the breakout lead
plugs into the existing wire
loom, and insert the two 4mm
banana plugs into the scope
using test lead HT30A, the
output signal can be taken. | For vehicle
testing. |
| |  6-Way Breakout Leads (HT306) | set | The lead is easy to access the
existing automotive wiring
harness interface, convenient to
read all kinds of sensor signal. | The lead with 4 kinds of joint
size: 0.6mm, 1.5mm, 2.3mm
and 2.8 mm. | For vehicle
testing. |
| |  Acupuncture Probe Set (HT307) | set | This acupuncture probe is a
back pinning, piercing and
repairable probe. | Contents: 5pcs complete
acupuncture probes, 2pcs screws,
20pcs replacement needles. | With
replacement
needles. |
| |  COP Extension Cord (HT308) | set | Simple accessory that allow you
to take accurate secondary
ignition measurements on
COP ignition systems. | Designed to aid diagnostics on
secondary ignition circuits by
allowing an HT measurement to
be made when there are no,
or limited access, to any
spark plug leads. | For vehicle
testing. |
| |  Auto Power Adapter (HT310) | pc | Power your oscilloscopes and
other electronic devices through
your vehicle's DC outlet with this
power adapter. | Input DC: 12-24VDC;
Output: 12V 1500mA
Cord Length: 1.45m. | Optional
car power
adapter and
cord for
oscilloscope. |
| |  BNC to 4 mm Adapter (HT311) | pc | The BNC to 4mm adapter
connects two 4mm banana
plugs to a BNC socket. | BNC Impedance: 50Ω
Voltage: 500V, Current: 3A Max.
Resistance: <0.8mΩ | Signal is
connected to
red terminal |
| |  LAN PCB (HT312) | pc | This board is factory installed on
oscilloscopes as an optional
interface and should require
no futher connections to be
made to it. | The LAN Interface PCB uses a
High Impedance Transceiver (HIT)
for signal transceiving in order to
utilize a bus topology on the LAN. | Optional
interface for
oscilloscope. |
| |  Mini Test Hook( HT321) | set | Set of 18 pcs mini test hooks
for logic analyzers and other
measuring instruments. | Hook connects to 1.65mm dia
wire or smaller. | Apply to
logic analyzer. |
| |  BNC to BNC Cable (HT322) | pc | It's an necessary interconnection
cable for general function and
signal generator applications. | 1m BNC male to BNC male
cable; Frequency range:DC~1GHz;
Nominal impedance: 50Ω;
Coaxial cable. | Male BNC
connectors on
both ends. |
| |  Multimeter Probe (HT325) | pair | Meter probe with standard plug
(4mm), suitable for universal. | CATIII 1000V, double insulation;
Max. rated current: 16A ;
Content: 1pc x red probe,
1pc x black probe | Adapt for
all Hantek
handheld
oscilloscope. |
| |  Multimeter Banana Socket (HT326) | set | 11.4mm multimeter banana plug
and socket, terminal test hole
and connector. | Set screw, high quality, 3 types
and many color available (red,
black, green, blue). | Accessory
for multimeter. |
| |  Multimeter Socket (HT323) | pair | The external multimeter socket
offer a quick and easy solution,
where a permanent connection
is not required. | Size: 11.4mm
Contents:
1pc x red socket
1pc x black socket | Accessory
for multimeter. |
