Select Model Unit Use Specification Other AC/DC Current Clamp CC-65
pc It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms. AC/DC Current Clamp, 20kHz Bandwidth, 1mV/10m, 65A. Two types connectors. Type A: Male BNC connector; Type B: Banana Connectors. AC/DC Current Clamp CC-650
pc It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms. AC/DC Current Clamp, 20kHz Bandwidth, 1mV/10m, 650A. Two types connectors. Type A: Male BNC connector; Type B: Banana Connectors. AC/DC Current Clamp CC-1100
pc It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms. AC/DC Current Clamp, 20kHz Bandwidth, 1mV/10m Two types connectors. Type A: Male BNC connector; Type B: Banana Connectors. Probe (PP80, PP90, PP150, PP200)
pc Integral injection molding makes the usage more flexible and the oscilloscope able to adapt more testing situations. Attenuation ratio: 1× and 10× optional. Input resistance: 1MΩ: 10MΩ System bandwidth: x1:DC-4MHz-80MHz; x10: DC-60MHz-200MHz. Universal version. High-Voltage x100 Probe (T3100)
pc The T3100 probe is designed as a strong, flexible and reliable part for the oscilloscope according to the human body function. Attenuation: 100:1; Input Resistance: 100M ohm; Bandwidth: DC-100MHz; Input Voltage:2000VDC+ACpk Universal version 20:1 Attenuator (HT201)
pc The HT201 has been designed to allow fuel injector and primary ignition waveforms to be measured using Hantek oscilloscopes. Specification: Attenuation: 20:1 Bandwidth: 10MHz Input Res: 1.053M For vehicle testing. Auto Ignition Probe (HT25)
pc Auto ignition probe is a kind of inductive capacitance sensor, it must match with an oscilloscope. Lead length 2.5 meters, the decay of up to 10,000:1. For vehicle testing. Large Dolphin/Gator Clips (HT18A)
pair The dolphin/gator clips are fully insulated with a 4 mm socket in the handle, offering an easy connection to the HT30A auto test cable. Length: 85 mm, Height: 38 mm Depth: 16.5 mm Clamping limit: 30 mm Contents:1pc X Red Clip 1pc X Black Clip Be able to use with HT30A. Multimeter Probe (HT19)
pair The multimeter probes offer a quick and easy solution, where a permanent connection is not required. Length: 131 mm Diameter: 10 mm Contents:1pc X Red Probe, 1pc X Black Probe Be able to use with HT30A and HT307. Auto Test Leads (HT30A)
pc It's a special line for assisting auto measurement instruments to test various types of signals. Test lead of a male BNC connector to (2) 4mm connectors. 4mm connectors are coded in two colors, black and red. Lead length 30 meter. For vehicle testing. Breakout Leads(HT301)
pc This breakout lead is easy to take voltage readings from numerous sensors in vehicle engine compartment. Connect the breakout lead plugs into the existing wire loom, and insert the two 4mm banana plugs into the scope using test lead HT30A, the output signal can be taken. For vehicle testing. 6-Way Breakout Leads (HT306)
set The lead is easy to access the existing automotive wiring harness interface, convenient to read all kinds of sensor signal. The lead with 4 kinds of joint size: 0.6mm, 1.5mm, 2.3mm and 2.8 mm. For vehicle testing. Acupuncture Probe Set (HT307)
set This acupuncture probe is a back pinning, piercing and repairable probe. Contents: 5pcs complete acupuncture probes, 2pcs screws, 20pcs replacement needles. With replacement needles. COP Extension Cord (HT308)
set Simple accessory that allow you to take accurate secondary ignition measurements on COP ignition systems. Designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there are no, or limited access, to any spark plug leads. For vehicle testing. Auto Power Adapter (HT310)
pc Power your oscilloscopes and other electronic devices through your vehicle's DC outlet with this power adapter. Input DC: 12-24VDC; Output: 12V 1500mA Cord Length: 1.45m. Optional car power adapter and cord for oscilloscope. BNC to 4 mm Adapter (HT311)
pc The BNC to 4mm adapter connects two 4mm banana plugs to a BNC socket. BNC Impedance: 50Ω Voltage: 500V, Current: 3A Max. Resistance: <0.8mΩ Signal is connected to red terminal LAN PCB (HT312)
pc This board is factory installed on oscilloscopes as an optional interface and should require no futher connections to be made to it. The LAN Interface PCB uses a High Impedance Transceiver (HIT) for signal transceiving in order to utilize a bus topology on the LAN. Optional interface for oscilloscope. Mini Test Hook( HT321)
set Set of 18 pcs mini test hooks for logic analyzers and other measuring instruments. Hook connects to 1.65mm dia wire or smaller. Apply to logic analyzer. BNC to BNC Cable (HT322)
pc It's an necessary interconnection cable for general function and signal generator applications. 1m BNC male to BNC male cable; Frequency range:DC~1GHz; Nominal impedance: 50Ω; Coaxial cable. Male BNC connectors on both ends. Multimeter Probe (HT325)
pair Meter probe with standard plug (4mm), suitable for universal. CATIII 1000V, double insulation; Max. rated current: 16A ; Content: 1pc x red probe, 1pc x black probe Adapt for all Hantek handheld oscilloscope. Multimeter Banana Socket (HT326)
set 11.4mm multimeter banana plug and socket, terminal test hole and connector. Set screw, high quality, 3 types and many color available (red, black, green, blue). Accessory for multimeter. Multimeter Socket (HT323)
pair The external multimeter socket offer a quick and easy solution, where a permanent connection is not required. Size: 11.4mm Contents: 1pc x red socket 1pc x black socket Accessory for multimeter.